typically the fan cooling the heatbreak and extruder stays on even with the “extruder” aka part cooler fan turned off

don’t get me wrong, getting a printer this big to run at those speeds must be quite a feat of precise engineering and craftsmanship. but in my opinion this machine is no more than a novelty; a machine no more capable than an off-the-shelf ender 3.

can you imagine producing a prototype from this machine? I have half a notion to build a profile for it in my slicer just to see how long I’d be waiting for a part 1m in any dimension.

is it cool? without a doubt. but FDM at this scale using 0.4mm to 1.0mm nozzles and 1.75mm filament is pointless. I think they missed the beat here by not engineering a hot end with greater extrusion capabilities. if it were fitted with, say, a 2mm nozzle it would be much more capable of producing large parts in a reasonable time frame.

curious machine. I’m surprised to see such mediocre specs with that price tag.

claims to be industrial yet uses 1.75mm hot end and can’t print any industrial grade materials

another thing to note… klipper firmware takes the heavy processing typically handled by the printer control board, and offloads the burden onto the computer or device you have hooked up to the printer, processing and feeding the gcode one line at a time. so whatever device you are using needs to be up to the specs. I’m using an rpi 3b+ and have no issues.

this project is awesome. thanks for sharing. now I want a v3

klipper is the firmware flashed to the printer

gui is achieved and accessed through mainsail or octoprint. I haven’t tried octoprint.

mainsail runs on a raspberry pi and can manage multiple klipper printers with one device. you can also add klipperscreen, it’s an addon that can be used with a touchscreen for an interface at the printer (or anywhere really)…

but I just access mine running mainsail through my phone browser or the laptop I use to model and slice. I like orcaslicer because it integrates mainsail right into a tab in the slicer and provides a seamless user experience.

even better, add [screws_tilt_adjust] to take advantage of the crtouch and a little fancy computer math to make leveling super easy.

after configuring the screw locations and thread pitch, execute the command screws_tilt_calculate

https://www.klipper3d.org/Manual_Level.html

ender beds use M4 screws

I ran a couple temp towers with the overture petg and I found 270-275c nozzle/80c bed had the most desirable results. 0.6 nozzle 0.4 layer height. also with the sprite pro.

I printed a couple pretty pieces before I started to get burnt crusty bits showing up in my prints so take this with a grain of salt. maybe due to me changing layer height to 0.14 without further testing.

maybe they are talking about the helicopters you can drive around in too. they don’t have big rotors on top, just basically a little fan in the front to cool the radiator when not in flight mode.

oh wait I’m thinking of a car

the caveat is that it had to once cost money? so stuff that has always been free is no longer available?

also weight gain. I worked 6pm-6am for almost 2 years straight and gained 40lbs without changing my eating habits.

started drinking every morning after work too. and days (nights) off were a total clusterfuck. wake up, hit the grocery store before they close, start drinking because wtf else am I gonna do at 11pm alone in my camper with no wifi and spotty cell signal. my experience is probably not the norm lol

my grandfather had alzheimer’s. dying from a side effect would have been better than the last 2 years of his life

meewow

I played so much Metal Gear Acid. when you get your deck tweaked just right and start cranking out the perfect combos it was so satisfying

mods seem to have less tolerance to bullshit

uh oh you’re making me nervous, bullshit is my specialty

no, it’s

when you are when you are tired stop don’t stop done

@MagsIFellFor